• Print quality (surface quality and amount of ringing) rapidly degraded with an increase in print speed
• A lack in frame sturdiness caused low quality parts from shaking induced by the moving axes
• Bolts loosened with use causing rapid degradation in calibration, giving rise to repeated long setup times
• The heat bed was underpowered and could not heat up quickly or reach temperatures above 95℃ (required to print certain plastics)
• Print volume was limited to 220x220x230mm The goal of this project is to design and build and improved, easy to run, budget 3D printer costing less than $750 for home users to create high quality, high speed prints with a minimum print volume of 275x275x325mm (2.475x107mm3). • Parts and materials must cost less than $750
• At a print speed of 60mm/s, ringing must be less than a 3 on a ringing scale of 1-6 (1 is negligible, 6 is significant) and roughness must be less than a 3 on a roughness scale of 1-6 (1 is smooth, 6 is rough)
• Print tolerance of ±0.2mm on a 25mm cube
• A minimum print volume of 275x275x325mm (2.475x107mm3)
• Sturdy frame and design
• Powerful heat bed capable of quickly heating to more than 110℃
The following tests were printed on both the Anet A8 and the new printer. The test prints were then compared and analyzed.
1. Calibration cubes (25x25x25mm) at print speeds from 30-80mm/s in 10mm/s steps with an acceleration of 1250mm/s2 testing for:
a. Ringing
b. Surface quality
c. Tolerance
2. #3DBenchys to test the ability to print difficult features (such as overhangs, bridges, complex rounded shapes, etc.)
3. Paper Basket Torture Tests to verify the maximum practical print volumes and identify any additional common printing issues
Critera and Constraints | Result |
---|---|
Parts and materials must cost less than $750 | ✓ |
At a print speed of 60mm/s, ringing must be less than a 3 on a ringing scale of 1-6 (1 is negligible, 6 is significant) and roughness must be less than a 3 on a roughness scale of 1-6 (1 is smooth, 6 is rough) | ✓ |
Print tolerance of ±0.2mm on a 25mm cube | ✓ |
A minimum print volume of 275x275x325mm (2.475x107mm3) | 4% less than theoretical due to V3 of Hotend Carriage |
Sturdy frame and design | ✓ |
Powerful heat bed capable of quickly heating to more than 110℃ | ✓ |
Warning! This project involves AC wiring and temperatures in excess of 200°C. Proceed only if you are sure that you know what you are doing!
Lay out four of the 470mm lengths of aluminum extrusion; this will create the bottom. Place an aluminum L-bracket at each intersection and start to tighten the screws. Use a square to make sure the frame is square. Repeat these steps for the top (using the remaining four 470mm extrusions). Next, attach the 440mm extrusions at the four corners of the bottom frame using two angle brackets. Use the square to check that the frame is still square. Finally, place the top on top of the 440mm extrusions and attach using the same method as the bottom. Tighten the screws fully while checking the entire frame for squareness.
Print all of the files in the Parts for IKEA Lack tables folder in the STL files folder as directed in Printed Parts.pdf. Attach the four type 1 Mounting/Strengthening Brackets to the bottom of the lower table. Next, place the upper table on top of the lower table and use four of the type 2 brackets to attach them together. Finally, attach the remaining four type 2 brackets to the underside of the upper table. To attach the casters, first push the caster adaptor onto the table leg. Next screw in the two drywall screws on the side. Finally, place the caster on top of the adaptor and screw in four of the 2" drywall screws.
Next, attach the main electronics (power supply, SSR, and Arduino/RAMPS combination) to the underside of the top table. Place the electronics as shown below and screw down using drywall screws. (I will cover the wiring later. You may notice that the power wires are soldered to the RAMPS board. That is because the RAMPS board I recieved did not come with an input jack. If your RAMPS also does not come with an input jack, either find an input jack or modify the RAMPS board as I did.)
For the filament storage, two PVC pipes are clamped on the sides of the upper IKEA Lack table with PVC Pipe Clamps and the remaining two pipes are clamped perpendicular to the sides with PVC Pipes Joiners. To install the PVC Pipe Clamps, carefully measure and mark half-way between the top and the bottom of the upper table on all four table legs. Next, using the square, create a line that passes through the marks on the legs. Place the PVC Pipe Clamp on the leg and mark where the holes should go. Finally, drill the holes and screw the PVC Pipe Clamps on. Slide a PVC pipe through one of the PVC Pipe Clamp, two of thw PVC Pipes Joiners and finally through the another PVC Pipe Clamp.
The next two steps involve using TAP Acrylic Cement, which contains a chemical that is suspected of causing cancer. Follow all precautions labelled on the can or use a different adhesive.
The finished hinges and door knobs can now be attached to the main door panels. First, mark out where the hinges and door knob are going to go on one panel. Space the hinges equidistant from each other on one side of the panel (the side of the hinge without the spacer should be on the panel, and the side with the spacer should be off the panel). As before, check that the hinges are placed far enough away from the edge of the panel so the edge does not interfere with the movement of the hinge. The knob can be placed halfway up the panel on the other side of the panel and around x cm in. Using the square to make sure the hinges and knob are aligned, apply acrylic cement as before. Repeat for the second panel.
Before attaching the acrylic panels to the IKEA Lack table, the seal strip should be applied. Peel back the plastic layer on the back of the strip to expose the adhesive. Apply the seal strip as shown in the picture below. (Cut the strip with a box-cutter or scissors.)
Holding a finished acrylic panel up to the front (or back) of the IKEA Lack table, mark out where the holes for the screws should go. Next, drill pilot holes. While holding the panel up, screw the screws in most of the way. (You may want to add a foam spacer to adjust the tension on the hinges from the seal strip.) Fine tune the depth the screws are screwed in to maximize the seal and minimize stress on the acrylic panel. Repeat for the second panel.
Now it is time to attach the toggle clamps and panel clamps to secure the acrylic panels. First print out the parts for the Acrylic Toggle Clamps and Acrylic Panel Clamps as directed in Printed Parts.pdf. The toggle clamps must be assembled before they are installed. Follow the steps demonstrated in the pictures to assemble the 10 total clamps. Install the toggle clamps as shown in the picture below by first marking out the locations with a pencil and the square, drilling pilot holes, and screwing in the screws (the edge of the clamp should be flush with the surface of the IKEA Lack table, but check for interference before drilling holes). The Acrylic Panel Clamps do not require assembly, but the installation is a bit trickier. Using the square and the acrylic panel and clamps for reference on the size, mark out where the panel clamps should go (see the picture below, and as before check for interference before installing). To install the set screws, drill pilot holes of 2.5mm. Now screw in the set screws. I found that the hex head on the set screw stripped immediately, so I used two nuts tightened together (as detailed in the picture below) to screw them in. See the picture below for what the finished installation should look like.
(to be added)
- Attach Printer to top table
- Create
- Install parts
- Bed supporting plate
- Print parts
- Add 10mm rods
- Bearings to bed supporting plate
- Z leadscrew and nut + parts
- Endstop and adjustable screw (cover software routine)
- Print parts
- Motor Mount
- Idler Bearing Mount
- 12mm Rod Clamp type 1 and 2
- Y endstop
- Motors
- Print parts
- aluminum rods and bushings
- Hotend carriage
- XY Joiner
- GT2 Belts
- Hotend install and fan install